Get product support, user manuals and software drivers for the LG AD600.AATTBK. View AD600.AATTBK warranty information & schedule repair service. To properly experience our LG.com website, you will need to use an alternate browser or upgrade to a newer version of internet Explorer (IE10 or greater). LG V50 ThinQ™ 5G (Verizon) A New Way to. LG offers the accessories to keep you connected and enhance your life. Take your mobile phone experience to another level with LG’s innovative line of accessories designed to make your life easier. Enhance your mobile experience with accessories from LG, the perfect companions to your favorite device.
![]()
I realize this is probably a little early to start a discussion for. I have a few of the new Verizon lte aircards and have had NO success in getting either wvdial to dial up to it or to have network manager do anything. Network manager recognizes it as eth1. When it tries to get a connection via dhcp, it spins for a while and I assume just times out. I assume there are going to be some sort of updates/extras to get these new sim card based aircards to make a connection through Linux.As I find out any new information, I will update this thread for any future searchers. Hidon't know much about these devicesif usb can see how it lists with this code if system 10.04, 10.10Code:usb-deviceslocate the lines which indicate the devicehopefully it will show the drivers involved, and may point as to where to lookfor possible areas as to how to connect - IE scan network - or configure and connectvia AT commands.
Hidon't know much about these devicesif usb can see how it lists with this code if system 10.04, 10.10Code:usb-deviceslocate the lines which indicate the devicehopefully it will show the drivers involved, and may point as to where to lookfor possible areas as to how to connect - IE scan network - or configure and connectvia AT commands. T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0D: Ver= 2.00 Cls=02(commc) Sub=02 Prot=01 MxPS=64 #Cfgs= 1P: Vendor=1004 ProdID=61aa Rev=01.00S: Manufacturer=LG ELECTRONICSIncS: Product=LG UDC-AHB SubsystemC: #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=400mAI: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdcetherI: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdcetherI: If#= 2 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdcacmI: If#= 3 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdcacmI see the first two cdcether entries. That must be its loading as ether1, although it can't pick up an address. Everything else in that entry is greek to me.I catch it appearing as ttyACM0 under dev when plugged in. My previous working wvdial.conf file fails however. I've been working on this today.
I got both the LG and the Pantech devices in today.The LG device is unresponsive. It does not give any responses to any commands on the tty port (and I tried turning echo on via ATE). Trying to bring up the ethernet interface only switches it to unknown state.The Pantech device is responds to commands.
![]() ![]()
I accedentally clobbered the pdp 1 context by trying an APN before first checking to see what it was set for. There were two other PDP contexts already configured as follows. Code: +CGDCONT: 3,'IPV4V6','vzwinternet','0.0.0.0',0,0+CGDCONT: 4,'IPV4V6','vzwapp','0.0.0.0',0,0Originally, I was able to get it to connect to the vzwinternet context. Pppd showed a successful authentication but then did not get any ip address or gateway.On Windows, the LG device was able to connect using CDMA but not LTE. The Pantech device was able to connect to LTE and got 16Mb downlink and 0.9Mb uplink. My next avenue will be to use a USB analyzer to find what the Windows software is doing.Last edited by PlancksCnst; December 9th, 2010 at 06:43 PM.Reason: updated statistics.
I've been working on this today. I got both the LG and the Pantech devices in today.The LG device is unresponsive.
It does not give any responses to any commands on the tty port (and I tried turning echo on via ATE). Trying to bring up the ethernet interface only switches it to unknown state.The Pantech device is responds to commands. I accedentally clobbered the pdp 1 context by trying an APN before first checking to see what it was set for. There were two other PDP contexts already configured as follows. Code: +CGDCONT: 3,'IPV4V6','vzwinternet','0.0.0.0',0,0+CGDCONT: 4,'IPV4V6','vzwapp','0.0.0.0',0,0Originally, I was able to get it to connect to the vzwinternet context.
Pppd showed a successful authentication but then did not get any ip address or gateway.On Windows, the LG device was able to connect using CDMA but not LTE. The Pantech device was able to connect to LTE and got 16Mb downlink and 0.9Mb uplink. My next avenue will be to use a USB analyzer to find what the Windows software is doing.Hican you post the details and sequence of the AT commands or commands send for each instancealso are you sending the commands direct, then calling the pppdthanks in advancealexfish.
![]() Comments are closed.
|
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2023
Categories |